MCO (Metal C-Ring for external pressure application)

To the overview
Metal C-Ring

External pressure application

MCO

For external pressure applications the inner diameter of the ring IDR is calculated as follows:

IDR = ID + Z

CSR Nominal cross-section: cross-sectional dimension (without coating) e.g. similar to the cord thickness of elastomer O-rings
Code Performance Index: shows characteristics of the ring (e.g. pressing load, springback)
D Groove depth: axial design dimension to which the ring is pressed from the original cross-section CSR.
F Pressing load: the mentioned guide values refer to 1mm seal length. To obtain the total load of the seal for the design of the construction, this value must be multiplied by the circumferential length of the seal.
ID Inner diameter of the groove: reference dimension for external pressure applications.
IDR min. Inner diameter of the ring: The inside diameter of the ring is freely selectable from the mentioned minimum dimension IDR min. and is at the same time the corresponding dimension to the inner diameter of the groove.
Pt coating thickness
R Radius: Design dimension that improves the support of the ring under pressure
SB Springback: maximum possible measure by which the ring can spring back elastically overall. Important value in connection with possible flange gaps.
Wmin groove width: radial design minimum dimension. The specified minimum dimension Wmin. must not be undercut.
Wt Wall thickness: sheet thickness of the ring.
Z diametric clearance between ring and groove.

The following ordering example describes a metal C-Ring for external pressure application Typ MCO in

7
Material Inconel 718
4,78
Cross section 4,78 mm
s
with wall thickness 0,76 mm
0230,48
Ring inner diameter IDR 230,48mm incl. coating
(suitable for groove inner diameter ID 230,00mm)
4
solution annealed and precipitation hardened
C
Copper coating
M
0.03 - 0.05 mm thick
MCO - 7 - 4,78 s - 0230,48 - 4 C M

Configure MCO

Metal O-Ring MCO Installation space Performance
Nominal
cross-section
Performance
index
Wall thickness Inner diameter
ring
diametrical
clearance
Groove depth Groove width Radius Pressing load
(Guide values)
Springback
(Guide values)
CSR
mm
Code Wt
mm
Ø IDR min.
mm
Z
mm
D
mm
Tol.
mm
W min.
mm
R max.
mm
F
ca. N/mm
SB
ca. mm
0,79 w 0,13 6 0,08 0,65 +0,05 1,10 0,25 35 0,04
0,79 s 0,18 6 0,08 0,65 +0,05 1,10 0,25 70 0,03
1,19 w 0,13 8 0,12 0,94 +0,05 1,40 0,30 20 0,05
1,19 s 0,20 8 0,12 0,94 +0,05 1,40 0,30 50 0,04
1,57 w 0,15 10 0,16 1,25 +0,10 2,00 0,35 25 0,08
1,57 s 0,25 10 0,16 1,25 +0,10 2,00 0,35 65 0,06
2,00 w 0,25 10 0,20 1,60 +0,10 2,30 0,45 45 0,06
2,20 w 0,25 10 0,22 1,75 +0,10 2,50 0,45 40 0,08
2,39 w 0,25 10 0,24 1,90 +0,10 2,70 0,50 50 0,12
2,39 s 0,38 10 0,24 1,90 +0,10 2,70 0,50 100 0,08
2,60 s 0,38 18 0,26 2,10 +0,10 2,85 0,50 80 0,10
2,79 w 0,38 18 0,28 2,23 +0,10 3,10 0,55 70 0,11
3,18 w 0,38 25 0,32 2,55 +0,10 3,50 0,75 60 0,15
3,18 s 0,51 25 0,32 2,55 +0,10 3,50 0,75 110 0,12
3,50 s 0,51 25 0,35 2,85 +0,10 3,85 0,75 50 0,14
3,96 w 0,41 35 0,40 3,20 +0,10 4,50 1,25 50 0,20
3,96 s 0,61 35 0,40 3,20 +0,10 4,50 1,25 120 0,17
4,78 w 0,51 45 0,48 3,85 +0,15 5,10 1,30 65 0,23
4,78 s 0,76 45 0,48 3,85 +0,15 5,10 1,30 150 0,18
5,00 w 0,51 75 0,51 4,00 +0,15 5,30 1,30 55 0,27
5,20 w 0,51 75 0,52 4,15 +0,15 5,50 1,30 55 0,28
5,60 w 0,51 80 0,56 4,50 +0,15 5,90 1,30 55 0,30
6,35 w 0,64 100 0,64 5,05 +0,20 6,60 1,50 70 0,35
6,35 s 0,97 100 0,64 5,05 +0,20 6,60 1,50 180 0,30
7,00 w 0,64 100 0,70 5,60 +0,20 7,65 1,50 70 0,35
7,90 w 0,97 100 0,79 6,35 +0,20 8,25 1,50 130 0,35
9,53 w 0,97 100 0,95 7,70 +0,30 9,70 1,50 110 0,50
9,53 s 1,27 100 0,95 7,70 +0,30 9,70 1,50 190 0,32
12,7 w 1,27 500 1,25 10,20 +0,30 12,70 1,50 130 0,55
12,7 s 1,65 500 1,25 10,20 +0,30 12,70 1,50 240 0,46

Mentioned performance guide values are valid for seals made from Inconel 718 solution annealed + precipitation hardened Std.
Preferred sizes are shown in bold. Other sizes not listed in table available on request.

Ring material

Ring material Code Material no.
SS304 1 1.4306
Inconel X-750 5 2.4669
Inconel 718 7 2.4668

Other materials on request.

Heat treatment

Heat treatment Code Description
HT 1 1 work hardened
HT 2 2 age hardened
HT 3 3 Solution annealing + precipitation hardened SC
HT 4 4 Solution annealing + precipitation hardened Std
HT 5 5 Heat treatment NACE MR 0175

Other treatments on request.

Coating

Coating Code max. temperature
Tin Z 200°C
PTFE P 290°C
Silver S 430°C (650°C*)
Copper C 930°C
Gold G 930°C
Nickel N 1200°C
without O

* Only valid for non-oxidizing media.
Other materials on request.

Coating thickness

Coating thickness Pt Code
0,01 - 0,03 mm L
0,03 - 0,05 mm M
0,05 - 0,07 mm H

Other coating thicknesses on request.

TOP ?

Uploads
Please feel free to add sketches, data sheets or technical drawings to your enquiry.
Allowed are jpg, jpeg and pdf up to max. 10 MB.


Data protection information *

Mandatory fields are marked with an *.